MAGNETS & ELECTRICITY • LEVEL 3

THE MAGNET WORKBENCH

Enough Talking — Let's Build Something!

You've learned what magnets do and how they interact with electricity. Now it's time to get your hands dirty, build real devices, take measurements, and discover what works.

Build It. Test It. Measure It. Discover Why.

Welcome to the Magnet Workbench!

This is where theory meets reality. You don't need expensive laboratory equipment. A few magnets, some copper wire, basic tools, and a little imagination can teach you a tremendous amount about electricity.

But we're going to do something different from many of those demonstration videos you see on the internet.

We're going to measure what actually happens.

Every experiment follows our laboratory method:

ASK PREDICT BUILD MEASURE DO IT AGAIN REPORT

Your Magnet Workbench Toolkit

Most of our experiments can be performed with inexpensive materials.

  • Small permanent magnets
  • Insulated copper magnet wire
  • Small permanent-magnet DC hobby motors
  • AA batteries and battery holders
  • Digital multimeter
  • Steel paper clips
  • Cardboard, tape, and wooden supports
  • Connecting wires and alligator clips
  • Small LED and suitable resistor
  • Safety glasses

You don't need everything at once. Start with the project that interests you.

PROJECT 01

Build a Simple Electric Motor

Can electricity and magnetism create continuous rotation?

An electric motor uses magnetic forces to turn electrical energy into mechanical motion. Let's build a simple demonstration.

Materials

  • One AA battery and holder
  • Approximately 60 cm of enamel-coated copper wire
  • Two large paper clips
  • One small permanent magnet
  • Electrical tape
  • Fine sandpaper

Build It

  1. Wind the copper wire into a circular coil of approximately 10 to 15 turns, leaving a straight wire end extending from each side.
  2. Wrap the ends around the coil to hold its shape, leaving the two straight ends pointing outward as an axle.
  3. On one axle end, remove all the enamel insulation where the support will touch it.
  4. On the other axle end, remove the enamel from only the upper half of the wire, keeping the lower half insulated. Keep the same orientation along the exposed axle.
  5. Bend the paper clips into supports and connect them to the battery holder terminals.
  6. Position the magnet beneath the coil.
  7. Rest the coil ends on the paper-clip supports so the coil rotates freely.
  8. Briefly connect the battery and gently nudge the coil to begin rotation.

What's Happening?

Current flowing through the coil creates a magnetic field. That field interacts with the permanent magnet and produces torque on the coil.

The half-stripped axle acts as a simple commutator, switching the current off during part of each rotation so the coil can continue turning in the same direction.

Experiment: Reverse the magnet. Does the direction of rotation change?

SAFETY: This is a low-resistance circuit that can heat the battery and wire quickly. Connect it only for a few seconds at a time. Disconnect immediately if anything warms up. Never leave it connected unattended. Use only a single AA battery, not a lithium battery or household electrical supply.

PROJECT 02

Turn a Motor Into a Generator

Can we reverse the process and turn motion into electricity?

Many small permanent-magnet DC motors can also function as generators. Instead of supplying electricity to make the shaft turn, we'll turn the shaft and measure the electricity produced.

Materials

  • Small brushed permanent-magnet DC motor
  • Digital multimeter
  • Connecting wires
  • Small wheel or hand crank

Build It

  1. Attach the wheel or crank to the motor shaft.
  2. Connect the multimeter to the motor terminals.
  3. Set the multimeter to DC voltage.
  4. Turn the shaft slowly and observe the voltage.
  5. Turn the shaft faster and record the result.
  6. Reverse the rotation and observe the polarity.

Record Your Measurements

TestRotationVoltage
1 Slow _____ V
2 Medium _____ V
3 Fast _____ V
4 Reverse _____ V

What Did We Learn?

A generator converts mechanical energy into electrical energy through electromagnetic induction.

In a typical small permanent-magnet DC motor, faster rotation produces greater voltage. Actual results depend on the motor and how consistently you turn it.

The important question: What supplied the energy?

Your hand supplied the mechanical energy. The motor converted some of it into electrical energy.

PROJECT 03

Magnetic Braking — Slow It Down Without Touching!

Can a magnet slow a moving object without touching it?

This experiment demonstrates eddy currents and Lenz's law, principles used in magnetic braking systems.

Materials

  • One thick-walled copper pipe
  • One small neodymium magnet that fits freely inside the pipe
  • One similar-sized nonmagnetic object
  • Stopwatch
  • Soft landing pad

Try It

  1. Hold the copper pipe vertically over a soft landing pad.
  2. Drop the nonmagnetic object through the pipe and observe its fall.
  3. Now release the magnet into the pipe without pushing it.
  4. Observe how slowly the magnet falls.
  5. Repeat the experiment and compare the results.

Why Does It Work?

As the magnet moves through the copper pipe, its changing magnetic field induces electrical currents in the copper. These are called eddy currents.

The currents create magnetic fields that oppose the change that produced them, slowing the falling magnet.

The lost mechanical energy is converted primarily into a tiny amount of heat inside the copper pipe.

The copper isn't strongly attracted to the magnet. The braking comes from electromagnetic induction!

SAFETY: Strong neodymium magnets can pinch fingers and are dangerous if swallowed. Keep them away from children, implanted medical devices, and sensitive equipment. Use a soft landing pad to prevent chipping.

PROJECT 04 — INVESTIGATING CLAIMS

Can Magnets Keep a Wheel Spinning Forever?

You've seen the videos. Now let's investigate the claim.

Some online demonstrations show wheels covered with magnets that appear to accelerate or spin continuously without an external power source.

The proposed explanation is often that magnetic attraction and repulsion keep pushing the wheel around.

Let's Ask the Right Questions

  • Where does the energy come from?
  • Does the wheel accelerate continuously?
  • How long does it spin without assistance?
  • Is there a hidden motor or power supply?
  • Can the experiment be independently reproduced?
  • Does it deliver measurable power to a load?

A Simple Investigation

Use a freely rotating, balanced wheel with a small magnet securely attached. Bring a second stationary magnet near its path and observe attraction and repulsion as the wheel rotates.

Notice that a magnet may accelerate the wheel during one portion of its rotation but resist its motion during another.

For a fixed arrangement of permanent magnets, the magnetic forces do not supply a continuous net energy gain over a complete cycle.

Friction and air resistance gradually remove mechanical energy, bringing the wheel to a stop unless additional energy is supplied.

A spinning wheel isn't proof of a self-powered generator.

To demonstrate useful energy generation, a machine must deliver measured electrical output while accounting for all energy entering the system.

SAFETY: Use a low-speed, hand-operated wheel with securely fastened magnets and a protective barrier. Do not use high-speed rotating magnets or unguarded power tools.

The Most Important Question in the Lab

WHERE DOES THE ENERGY COME FROM?

Magnets are extraordinary tools. They allow motors to turn, generators to produce electricity, and countless machines to operate.

But magnets are not an unlimited source of usable energy.

In a generator, mechanical energy is converted into electrical energy. The magnetic field makes that conversion possible.

When a generator supplies power to a load, the mechanical drive must provide the corresponding energy, plus additional energy to overcome losses.

Don't confuse energy conversion with energy creation.

Become a Better Experimenter

Before declaring an experiment a success or failure, record:

  • Materials and equipment used
  • Magnet type and dimensions
  • Coil turns and wire size, where applicable
  • Voltage and current measurements
  • Rotation speed or operating time
  • Input energy and output energy, where measurable
  • Unexpected behavior
  • Results from repeated tests

Remember that voltage alone doesn't tell us how much useful electrical power a device delivers.

Electrical Power (Watts) = Voltage (Volts) × Current (Amps)

For DC measurements, this formula applies to the voltage across and current through the load. For AC circuits, power factor and waveform may also matter.

Record measurements under a real load before making claims about useful output.

The Workbench Is Just Getting Started!

Today we've explored motors, generators, magnetic braking, and the fascinating claims surrounding magnetic machines.

There are plenty more experiments waiting to be built, measured, and understood.

Don't Just Believe It.
Don't Just Doubt It.
TEST IT!

Alternative Energy Lab